跳到主要內容

Port-Security (暫)

Switch(config-if)#switchport port-security
Command rejected: FastEthernet0/2 is a dynamic port.

Switch(config-if)#switchport mode access
Switch(config-if)#switchport port-security
Switch(config-if)#switchport port-security maximum 1
Switch(config-if)#switchport port-security mac-address sticky
Switch(config-if)#switchport port-security violation restrict


Switch(config-if)#switchport port-security violation ?
  protect   Security violation protect mode
  restrict  Security violation restrict mode
  shutdown  Security violation shutdown mode



Switch#show port-security
Secure Port  MaxSecureAddr  CurrentAddr  SecurityViolation  Security Action
                (Count)       (Count)          (Count)
---------------------------------------------------------------------------
      Fa0/2              1            1                  0         Shutdown
---------------------------------------------------------------------------
Total Addresses in System (excluding one mac per port)     : 0
Max Addresses limit in System (excluding one mac per port) : 1024

Switch#show port-security add
Switch#show port-security address
          Secure Mac Address Table
-------------------------------------------------------------------
Vlan    Mac Address       Type                Ports   Remaining Age
                                                         (mins)
----    -----------       ----                -----   -------------
   1    000e.a6f9.2d53    SecureSticky        Fa0/2        -
-------------------------------------------------------------------
Total Addresses in System (excluding one mac per port)     : 0
Max Addresses limit in System (excluding one mac per port) : 1024

Switch#show port-security interface fa 0/2
Port Security              : Enabled
Port Status                : Secure-up
Violation Mode             : Shutdown
Aging Time                 : 0 mins
Aging Type                 : Absolute
SecureStatic Address Aging : Disabled
Maximum MAC Addresses      : 1
Total MAC Addresses        : 1
Configured MAC Addresses   : 0
Sticky MAC Addresses       : 1
Last Source Address        : 7c61.93af.fe88
Security Violation Count   : 0

留言

這個網誌中的熱門文章

使用Cisco L3 Switch做VLAN的Routing

目標: 讓VLAN100與VLAN200的電腦透過L3 Swtich做VLAN的Routing,並且可以互相存取資源與上網,另外再使用Windows Server 2012配發VLAN100,VLAN200的IP Firewall: 使用ASUS AP當Firewall,並設兩條Static Route Switch: Core Switch為Cisco 3750切VLAN 10,VLAN100,VLAN200,VLAN10為預設的VLAN,VLAN100為Sales,VLAN200為RD Edge Switch為Cisco 3750與2950,其中2950為VLAN100,3750為VLAN200,如果要By Port切VLAN也可以,這裡只是為了方便說明,所以Edge Switch都直接設為單一VLAN Core Switch的設定 原本我只想Show Running-config其中比較重要的設定,後來想想還是全部列出,用紅色標記重要的設定 Gi 1/0/1接2950 Gi 1/0/2接3750 Gi 1/0/24接Router Core-3750#show running-config Building configuration... Current configuration : 2436 bytes ! version 12.2 no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname Core-3750 ! boot-start-marker boot-end-marker ! ! ! ! no aaa new-model switch 1 provision ws-c3750g-24t system mtu routing 1546 ip routing no ip domain-lookup ! ! ! ! ! ! ! ! spanning-tree mode pvst spanning-tree portfas...

Cisco Switch 發生Loopback

User告知網路無法使用,看了Switch的狀況後,發現那個Port的狀態是Error Disable,接著又看了Switch的log Feb  8 12:14:14 TW: %DHCP_SNOOPING-5-DHCP_SNOOPING_UNTRUSTED_PORT: DHCP_SNOOPING drop message on untrusted port, message type: DHCPNAK, MAC sa: 2c56.dc86.xxxx Feb  8 12:15:49 TW: %DHCP_SNOOPING-5-DHCP_SNOOPING_UNTRUSTED_PORT: DHCP_SNOOPING drop message on untrusted port, message type: DHCPNAK, MAC sa: 2c56.dc86.xxxx Feb  8 12:18:00 TW: %ETHCNTR-3-LOOP_BACK_DETECTED: Keepalive packet loop-back detected on FastEthernet0/10. Feb  8 12:18:00 TW: %PM-4-ERR_DISABLE: loopback error detected on Fa0/10, putting Fa0/10 in err-disable state Feb  8 12:18:01 TW: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/10, changed state to down Feb  8 12:18:02 TW: %LINK-3-UPDOWN: Interface FastEthernet0/10, changed state to down 應該是User私接設備,除了造成Loopback之外,又在隨便發放IP....... 不過因為那個User比較特殊,先教育了一下之後,再把那個Port shutdown , no shutdown,接著把Recovery設了上去,下次如果再遇到相同狀況,10分鐘後會自動恢復 xxx...

2台 Vigor 2920建立 LAN To LAN VPN (IPsec)

我有兩台Vigor 2920,環境如下: Vigor B 撥出 LAN:192.168.1.0/24 Vigor A 撥入 LAN:172.16.1.0/24 設定如下: Vigor B設定 Vigor A設定 詳細設定請參考官網 http://www.draytek.com/index.php?option=com_k2&view=item&id=2666&Itemid=264&lang=tw