寫寫筆記

Brocade ICX6430 Switch 啟用 DHCP Snooping 假設我的DHCP Server接在24 Port，其他Port不允許有DHCP Server ICX6430-24 Switch> enable No password has been assigned yet... ICX6430-24 Switch# configure terminal ICX6430-24 Switch(config)# ip dhcp snooping vlan 1 ICX6430-24 Switch(config)# interface ethernet 1/1/24 ICX6430-24 Switch(config-if-e1000-1/1/24)# dhcp snooping trust 預設Spanning Tree是開啟的,我把Port 9與Port 11接成Loop ICX6430-24 Switch# show span STP instance owned by VLAN 1 Global STP (IEEE 802.1D) Parameters:      Root             Root Root   Prio Max He- Ho- Fwd Last    Chg Bridge       ID              Cost Port   rity Age llo ld  dly Chang   cnt Address                                   Hex  sec sec sec sec sec      8000cc4e2434dda0 0    Root ...

兩個Cisco 2950 Switch , 第一台與第二台的Port 1 與 Port 2 對連，設定EtherChannel 第一台Switch up# configure terminal Enter configuration commands, one per line.  End with CNTL/Z. up(config)# interface range fastEthernet 0/1 - 2 up(config-if-range)# no ip address up(config-if-range)# channel-group 1 mode desirable Creating a port-channel interface Port-channel 1 第二台Switch down# configure terminal Enter configuration commands, one per line.  End with CNTL/Z. down(config)# interface range fastEthernet 0/1 - 2 down(config-if-range)# no ip address down(config-if-range)# channel-group 1 mode desirable Creating a port-channel interface Port-channel 1 down(config-if-range)# 00:34:30: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down 00:34:30: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down 00:34:33: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up 00:34:...

啟動DHCP Snooping 假設我的DHCP Server接在24 Port，其他Port不允許有DHCP Server C3750(config)# ip dhcp snooping C3750(config)# ip dhcp snooping vlan 1 C3750(config)# interface gigabitEthernet 2/0/24 C3750(config-if)# ip dhcp snooping trust C3750(config-if)# do show ip dhcp snooping Switch DHCP snooping is enabled DHCP snooping is configured on following VLANs: 1 DHCP snooping is operational on following VLANs: 1 DHCP snooping is configured on the following L3 Interfaces: Insertion of option 82 is enabled    circuit-id default format: vlan-mod-port    remote-id: 0016.9d99.3e80 (MAC) Option 82 on untrusted port is not allowed Verification of hwaddr field is enabled Verification of giaddr field is enabled DHCP snooping trust/rate is configured on the following Interfaces: Interface                  Trusted    Allow option    Rate limit (pps) -----------------------    -------   ...

沒用過HP的Switch，指令跟Cisco完全不同，花了一些時間熟悉~ 1.啟動Spanning-Tree，預設沒有開啟 (黑色粗體是我敲的指令) <HP> system-view System View: return to User View with Ctrl+Z. [HP] stp enable [HP] %Apr 26 12:03:59:826 2000 HP MSTP/6/MSTP_ENABLE: STP is now enabled on the device. %Apr 26 12:03:59:918 2000 HP MSTP/6/MSTP_FORWARDING: Instance 0's GigabitEthernet1/0/17 has been set to forwarding state. %Apr 26 12:04:00:068 2000 HP MSTP/6/MSTP_DETECTED_TC: Instance 0's GigabitEthernet1/0/17 detected a topology change. #Apr 26 12:04:00:208 2000 HP MSTP/1/PFWD: hwPortMstiStateForwarding: Instance 0's Port 0.9437200 has been set to forwarding state! 2.DHCP Snooping   (黑色粗體是我敲的指令) 假設我的DHCP Server接在24 Port，其他Port不允許有DHCP Server <HP> system-view System View: return to User View with Ctrl+Z. [HP] dhcp-snooping  DHCP Snooping is enabled. [HP] interface GigabitEthernet 1/0/24 [HP-GigabitEthernet1/0/24 ]dhcp-snooping trust 若是沒有Port 設成dhcp-snooping trust,那麼這台Switch就沒有Client可以從DHCP Serv...